桂林-阳朔地区DEM地形特征与岩性相关性分析及分类研究

地形地貌是岩性解译的重要信息,地形因子作为描述DEM数字曲面几何特征的定量指标参数,可用来定量化表达不同岩性所在地区地形地貌特征。本文以桂林-阳朔地区为研究区,研究地形因子数学、地质意义,建立岩性与地形因子组合间的定量关联,进而实现岩石类型划分。本文基于ASTERGDEM提取坡度、起伏度等12个地形因子,在分析各个地形因子地质意义基础上,通过聚类分析及方差分析的多元统计分析方法,研究各岩性地形因子特性及其关联性,建立研究区岩性之间的定量差异;此外,利用因子分析方法研究岩性分类过程中的主导因素,确定适宜岩性分类方法以实现定量化岩性分类。实验结果表明：不同岩性、不同地形地貌的地形因子（组合）之间具有显著差异,基于因子分析得到的宏观地形复杂度指数（MTI）以及微观曲率指数（MCI）对岩石类型的分类精度达77.36%。研究表明,地形复杂度等地形因子可用于岩性分类,采用因子分析方法可获取反映地形地貌宏观、微观特征的定量指标,且岩性分类效果良好。     

青州市表层土壤元素地球化学组合特征研究

聚类分析和因子分析可以获得土壤元素地球化学组合特征及其差异性。对青州市表层土壤样品数据进行分析研究,通过聚类分析,绘制表层土壤元素聚类谱系图,将23种元素或指标分为5个元素组合簇群及2个单元素簇,研究各元素间的组合特征,探讨其相关性、聚集性及其指示意义;通过因子分析,找出有代表性的因子,用其代表变量,绘制典型因子得分等值线图,并从中分析不同元素组合的区域分布基于何种因素,用11个代表性因子的分布特征就基本可以代表青州市表层土壤23项原始变量的分布特征,并对F1,F2,F3主因子进行了地质解释。聚类分析与因子分析相结合,利于表层土壤中元素的共生组合特征及其差异性研究,利于对研究区表层土壤异常进行归纳总结。     

Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.     

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.     

Analytical study of ground motion caused by seismic wave propagation across faulted rock masses

Studying seismic wave propagation across rock masses and the induced ground motion is an important topic, which receives considerable attention in design and construction of underground cavern/tunnel constructions and mining activities. The current study investigates wave propagation across a rock mass with one fault and the induced ground motion using a recursive approach. The rocks beside the fault are assumed as viscoelastic media with seismic quality factors, Q_p and Q_s. Two kinds of interactions between stress waves and a discontinuity and between stress waves and a free surface are analyzed, respectively. As the result of the wave superposition, the mathematical expressions for induced ground vibration are deduced. The proposed approach is then compared with the existing analysis for special cases. Finally, parametric studies are carried out, which includes the influences of fault stiffness, incident angle, and frequency of incident waves on the peak particle velocities of the ground motions.     

Properties of geogrid-reinforced marine slope due to the groundwater level changes

Evaluation of slope stability, especially in the absence of a proper bed such as marine soils, is one of the most important issues in geotechnical engineering. Using geogrid layers to enhance the strength and stability of embankments is regarded as a commendable stabilization method. On the other hand, groundwater level erratically fluctuates in coastal areas. Therefore, the aim of this research is to study the effects of groundwater level changes on stability of a geogrid-reinforced slope on loose marine soils in Qeshm Island, Iran. At first, geotechnical properties of the site were obtained by comprehensive series of geotechnical laboratory and in situ tests. Then, by simultaneous changes of groundwater level and several parameters such as embankment slope, loading, geogrid length, geogrid number, and tensile strength of geogrid, different characteristics such as embankment safety factor (SF), vertical and horizontal displacements at embankment top and embankment base were studied. It was observed that groundwater level had significant effects on behavior of the embankment. For most of the observations, by decreasing the groundwater level, the displacements decreased and consequently safety factor increased. Increasing the length, number, and tensile strength of geogrid led to the reduction of displacements and an increase in the safety factor.     

深水铺管船托管架疲劳分析及动态监测点选取研究

作为S型铺管作业的关键性装备,托管架长期承受着交变载荷的作用,随着海洋开发向超深水发展,结构疲劳破坏问题不容忽视。采用疲劳谱分析的方法并结合线性累积损伤理论,对托管架结构频域下的变形进行了分析,计算了正常海况下和极端海况下托管架疲劳损伤度并对疲劳寿命进行了评估。研究发现托管架在正常海况下作业符合安全要求,在极端海况下局部结构会受到破坏。并从托管架结构安全监测角度,筛选了结构疲劳分析关键点位,为监测点位的选取提供了依据。     

Micromechanical approach to effective viscoelastic properties of micro‐fractured geomaterials

The aim of this paper is to formulate a micromechanics‐based approach to non‐aging viscoelastic behavior of materials with randomly distributed micro‐fractures. Unlike cracks, fractures are discontinuities that are able to transfer stresses and can therefore be regarded from a mechanical viewpoint as interfaces endowed with a specific behavior under normal and shear loading. Making use of the elastic‐viscoelastic correspondence principle together with a Mori‐Tanka homogenization scheme, the effective viscoelastic behavior is assessed from properties of the material constituents and damage parameters related to density and size of fractures. It is notably shown that the homogenized behavior thus formulated can be described in most cases by means of a generalized Maxwell rheological model. For practical implementation in structural analyses, an approximate model for the isotropic homogenized fractured medium is formulated within the class of Burger models. Although the approximation is basically developed for short‐term and long‐term behaviors, numerical applications indicate that the approximate Burger model accurately reproduce the homogenized viscoelastic behavior also in the transient conditions.     

基于细分行业的安徽省创新型企业集聚研究

创新型企业作为塑造创新地理格局的重要力量，其区位选择的外部特征及内在机理亟须予以系统化研究。基于对安徽省创新型企业的细分行业与空间建库，采用核密度估计和地理探测器等方法，对细分行业下的创新型企业空间集聚特征及影响因素进行研究。结果表明：（1）安徽省创新型企业类型以先进制造和自动化为主，并以生物与新医药、新材料、电子信息为辅；（2）创新型企业空间集聚的不均衡特征显著，呈现出“一核一带多节点”的集聚分布特征，且合肥、芜湖是两个重要集聚区；不同细分行业视角下创新型企业的空间分布形态各异，可归纳为点-轴式、极核式、双核式及多核分散式等4种空间组织形态。（3）创新型因子对于创新型企业的空间集聚最为重要，但传统型和政策型因子的重要性仍不容忽视。其中，产业基础、人力资本、创新投入是最核心的因素，但各行业创新型企业的影响因素作用力则表现出一定的异质性。     

Smeared crack approach: back to the original track

This paper briefly reviews the formulations used over the last 40 years for the solution of problems involving tensile cracking, with both the discrete and the smeared crack approaches. The paper focuses on the smeared approach, identifying as its main drawbacks the observed mesh‐size and mesh‐bias spurious dependence when the method is applied ‘straightly’. A simple isotropic local damage constitutive model is considered, and the (exponential) softening modulus is regularized according to the material fracture energy and the element size. The continuum and discrete mechanical problems corresponding to both the weak discontinuity (smeared cracks) and the strong discontinuity (discrete cracks) approaches are analysed and the question of propagation of the strain localization band (crack) is identified as the main difficulty to be overcome in the numerical procedure. A tracking technique is used to ensure stability of the solution, attaining the necessary convergence properties of the corresponding discrete finite element formulation. Numerical examples show that the formulation derived is stable and remarkably robust. As a consequence, the results obtained do not suffer from spurious mesh‐size or mesh‐bias dependence, comparing very favourably with those obtained with other fracture and continuum mechanics approaches. Copyright © 2006 John Wiley & Sons, Ltd.